An active alignment (AA) bonding adhesive fixes the lens in a camera module once it has been set to the sharpest position. Dual-cure types are most common: UV locks the position in seconds and a heat cure delivers the final strength.
As camera resolution rises, mechanical tolerances alone can no longer place the lens accurately enough over the sensor. High-resolution camera modules are therefore assembled by AA, aligning the lens while the sensor is powered and the image is watched. The adhesive's job is to hold that aligned position exactly.
How the AA process runs
- Adhesive is dispensed as a bead on the lens holder joint.
- With the sensor powered, the lens position and tilt are adjusted on several axes while watching a test chart.
- At the position where the whole image is sharpest, UV is applied to fix the lens in seconds.
- An oven heat cure finishes the areas UV could not reach and builds final strength.
Why use both UV and heat
- UV only: areas the light cannot reach, such as under the holder or in a component's shadow, stay under-cured.
- Heat only: the lens can move while the adhesive cures, shifting the focus that was just set.
- Both: UV locks the aligned position immediately, and the heat cure completes the shadowed areas and final bond strength.
What to check in an AA adhesive
- Shape retention: if the bead slumps during alignment, the lens-to-holder gap changes. A high-TI adhesive helps.
- Shift during cure: small movements between UV fixing and the end of heat cure show up as focus shift. Compare focus before and after cure on real modules.
- Heat cure temperature: modules with plastic lens holders or IR filters benefit from a lower cure temperature.
- Shock and vibration: the lens must stay put through phone drops and vehicle vibration.
COFA 1001D
1001D (catalog designation 1001UH) is a UV and heat dual-cure epoxy. It is fixed with UV at 3,000 mJ and then heat cured at 80°C for 60 minutes. With a TI of 4.8 it holds the dispensed bead shape well, and its cured hardness is Shore D 92. Increased crosslinking between the epoxy and acrylic components is designed to resist thermal and mechanical stress, shock and vibration.
| Property | Value |
|---|---|
| Chemistry | Epoxy (UV and heat dual cure) |
| Color | Ivory |
| Viscosity | 30,000 cps |
| TI | 4.8 |
| Hardness | Shore D 92 |
| Moisture absorption | 0.51% (100°C / 100% RH, 1 h) |
| Work life | 48 h (25°C) |
| Cure | UV 3,000 mJ + 80°C / 60 min |
Applications
- Active alignment bonding in smartphone and vehicle camera modules
- Optical sensor module assembly
- Structural bonding of semiconductor devices exposed to shock and vibration
Frequently asked questions
What is active alignment (AA) bonding?
In camera module assembly, the image sensor is powered and the lens position is fine-tuned on several axes while watching the live image. Once the sharpest position is found, the lens is fixed with adhesive. It is used to match focus and resolution across the whole image in high-resolution cameras.
Why use a UV and heat dual-cure adhesive for AA?
UV fixes the lens in seconds the moment alignment is done, and an oven cure delivers the final strength. UV alone leaves shadowed areas such as under the holder under-cured, and heat alone lets the lens drift while the adhesive cures.
Why is a high TI useful in AA adhesives?
A high-TI adhesive keeps the shape of the dispensed bead. It must not slump or spread during alignment, so the gap between lens and holder stays consistent.
What is the cure schedule for COFA 1001D?
UV at 3,000 mJ for initial fixing, followed by a heat cure at 80°C for 60 minutes. With an 80°C heat cure, it can be evaluated for modules with heat-sensitive parts such as plastic lens holders.
Where is COFA 1001D used?
Active alignment bonding in camera modules, optical sensor modules, and structural bonding of semiconductor devices exposed to shock and vibration. Its cured hardness is Shore D 92.
Share your process conditions
Tell us your package type, bump pitch and gap, dispensing method and cure profile, and we will review the right grade and an evaluation plan with you.
Published 2026-11-03 · COFA Co., Ltd. technical team